Search results

The feet may be tight but it should fit may need to relieve the cut outs slightly with a file but don't modify the detector worst case if you need a spacer for between the top and base section I can make you one let me know how thick it needs to be to allow the legs to fit and bolt up. Regards, Ian.

Well it would be nice to have got a response to know that you got what I sent you ok at least to my knowledge you received the package last Thursday I have added an image of what I sent. Regards, Ian.

Hi Mr Yarg no problem just get your existing cable shortened you have the plugs and you will only need about 300mm max of cable if you make a pocket on the detector cover to carry the battery I have responded to your message. Regards, Ian.

Thank you gef12. Mr Yarg, If you are going to use the camcorder type batteries I have an early version of the battery carrier I use that the battery is held in place with Velcro rather than the lock I now use it is surplus to my requirements so you are welcome to it if you want it no cost just...

You can also get these batteries at 12 ah and this is what I use for my GPX5000 the battery holder below is what I made to solve connections it will run my F1A4 or GPX depending on input cables I have one for each detector the only problem I see is I am not sure the GP 3500 will work with the...

Give Hack's Bridge area a try between Mylor and Echunga there is a small park on the Echunga side of the bridge that has access to the river and it does hold colour well known spot worked by the old boys. Regards, Ian.

Hi Mr Yarg, The original Gel cells should last out the day depending how old they are as for your 18V Milwaukee battery's this would work with a voltage regulator but do not try to run the GP3000 direct from the 18V battery or bad smoke will appear I do have a circuit for a suitable voltage...

Yes correct. Regards, Ian.

John if you get stuck I am over on the SYP I have a chain mill and could crush the rocks for you if you are over this way. Regards, Ian.

Looks good should also fit the 5000, Is the gcode available. Regards, Ian.

Looks like problem solved with your 17 x 13 pull the plug apart cut two inches off and re terminate and hopefully that may fix it pity you are too far away from me I would attempt to repair it for you. Regards, Ian.

I would expect at least 4" for the .5 as I know I get at least that with a 17" DD Pro and 3500 the Evo should be fine or an old 24" UFO if you can find one. Regards, Ian.:)

Les PM me your Email address and I will give you the info you need. Regards, Ian.

If you can pair more than one device to the Bluetooth TX then Yes I do not have any GPX6000 experience but I can with my Bluetooth TX and the GPX5000 and the F1A4 and QED I do it into my Hearing Aids. Regards, Ian.

Hi Bontje, To answer your first question Yes go onto the SARIG map go down to All Map Layers until you get to Mines and minerals- by commodity tick that and in that tick Gold and carry on down until you get to Mines and Mineral deposits - by activity tick that and just below that tick...

Spotlight or DD leather. Regards, Ian.

Hi Nikki, Do not be put off I spend 95% of my time in S.A. and you have choices not too far from home in the Flinders Ranges you just need to do some research we don't have the amount or size of nuggets that our adjourning states have but they are there just a bit more work is needed and lots...

To clip the leads into to stop pulling on the plugs and breaking wires. Regards, Ian.

Me too VK5KIB also ex G6HMH when I went to the UK for work in 1981/1982 not very active but still have my gear especially Codan in the cruiser with ham bands programmed in. Regards, Ian.

Ok firstly Most coil housings are made with ABS plastics and bond easily with a mixture of ABS offcuts and MEK or clear plumbing primer which is easier to get hold of for the lay person for my home made coils I fabricate the coil ears with ABS sheet and bond them onto the housings and never had...